Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- know-how:etc [2024/04/19 10:23] – [Micro Firewall - HUNSN] cc
+++ know-how:etc [2024/05/29 16:08] (aktuell) – [Unifi-Controller] cc
@@ Zeile 653: / Zeile 653: @@
 |Magenta Mobilfunk - Smartphone Tarif|-|**keine Sperre** bei TCP/25|
+===== Unifi-Controller =====
+  * Im Einsatz mit Debian Bullseye / virtualisiert auf einem Debian Bullseye System
+  * Unter **Network** die verkabelten Netze zB: VLAN Tagging - und unter **WiFi** die WLANs die mit den Netzwerken zusammen gehängt werden / **Default** ist das untagged VLAN bzw. access Netz
+  * Installation/Scratchpad:
+<code>
+Official:
+Testing with debian bullseye
+https://help.ui.com/hc/en-us/articles/220066768-Updating-and-Installing-Self-Hosted-UniFi-Network-Servers-Linux
+UniFi Network APT Steps
+See an example of what scripts the UI Community is using to install and update the UniFi Network Server on any Ubuntu or Debian-based system in this Community post.
+      Install required packages before you begin with the following command:
+      sudo apt-get update && sudo apt-get install ca-certificates apt-transport-https
+      Use the following command to add a new source list:
+      echo 'deb [ arch=amd64,arm64 ] https://www.ui.com/downloads/unifi/debian stable ubiquiti' | sudo tee /etc/apt/sources.list.d/100-ubnt-unifi.list
+      Add the GPG Keys.
+          Method A - Recommended
+              Install the following trusted key into /etc/apt/trusted.gpg.d
+              sudo wget -O /etc/apt/trusted.gpg.d/unifi-repo.gpg https://dl.ui.com/unifi/unifi-repo.gpg
+           Method B
+              Using apt-key:
+              sudo apt-key adv --keyserver keyserver.ubuntu.com --recv 06E85760C0A52C50
+      For a new UniFi Network Server, install MongoDB. For Ubuntu 22.04, run the commands below. If you're updating the UniFi Network Server to version 7.5, ignore these commands and instead refer to MongoDB's help article (or use this community script) to update your database to the required MongoDB version 3.6.
+      wget -qO - https://www.mongodb.org/static/pgp/server-3.6.asc | sudo apt-key add -
+      echo "deb [trusted=yes] https://repo.mongodb.org/apt/ubuntu bionic/mongodb-org/3.6 multiverse" | sudo tee /etc/apt/sources.list.d/mongodb-org-3.6.list
+      sudo apt-get update
+      This step may not be required, depending on the Linux distro you have. If your distro does not come with MongoDB, and it's not available in their repo, then please see the MongoDB installation guide (Ubuntu | Debian).
+      Install and upgrade the UniFi Network application with the following command:
+      sudo apt-get update && sudo apt-get install unifi -y
+      The UniFi Network application should now be accessible at the computer's configured local or public IP address, by typing that IP address in a browser's navigation bar (Chrome is recommended). If it is not launching, use the following command:
+      sudo service unifi start
+When using the commands above, it is assumed you have sudo and wget installed. More information about sudo can be found here, and wget here.
+Other Helpful Commands
+      To stop the UniFi service: sudo service unifi stop
+      To restart the UniFi service: sudo service unifi restart
+      To see the status of UniFi service: sudo service unifi status
+Click here for possible suite names and code names.
+Log Files Location
+Log files are essential for any troubleshooting. Find them here:
+      /usr/lib/unifi/logs/server.log
+      /usr/lib/unifi/logs/mongod.log
+If your application is running on a Unix/Linux based system, then you will require superuser (sudo) privileges to access these log files.
+-----
+Mongo DB:
+https://gist.github.com/sinofool/233ed96dd85123ee5a87ad12e812d424?permalink_comment_id=4129590
+# MongoDB 4.4, [end of life Feb 2024](https://www.mongodb.com/support-policy/lifecycles)
+curl -fsSL https://pgp.mongodb.com/server-4.4.asc | sudo gpg -o /usr/share/keyrings/mongodb-server-4.4.gpg --dearmor
+echo "deb [ signed-by=/usr/share/keyrings/mongodb-server-4.4.gpg ] http://repo.mongodb.org/apt/debian buster/mongodb-org/4.4 main" | sudo tee /etc/apt/sources.list.d/mongodb-org-4.4.list
+sudo apt-get update && sudo apt-get install mongodb-org-server -y
+# Unifi
+sudo apt-get update && sudo apt-get install -y ca-certificates apt-transport-https
+curl -fsSL https://dl.ui.com/unifi/unifi-repo.gpg | sudo gpg -o /usr/share/keyrings/unifi-repo.gpg --dearmor
+echo 'deb [ signed-by=/usr/share/keyrings/unifi-repo.gpg ] https://www.ui.com/downloads/unifi/debian stable ubiquiti' | sudo tee /etc/apt/sources.list.d/100-ubnt-unifi.list
+sudo apt-get update && sudo apt-get install unifi -y
+apt-get -f install unifi
+</code>
+{{:know-how:0-unifi-controller-untagged-dhcp-accesspoint.png?400|}}
+{{:know-how:1-unifi-controller-untagged-dhcp-accesspoint-adopt-device.png?400|}}
+{{:know-how:2-unifi-controller-upgrade-access-point.png?400|}}
+{{:know-how:3-unifi-controller-network-wlan.png?400|}}
+{{:know-how:4-unifi-controller-network-vlans.png?400|}}
+{{:know-how:5-unifi-controller-provision-new-ap6-pro.png?400|}}
 ====== Hardware ======
@@ Zeile 1578: / Zeile 1672: @@
   * **Lösung:**  DisplayPort auf HDMI Adapter einstecken bei Display Port zB: https://www.amazon.de/gp/product/B010SDZZ80/ref=ppx_yo_dt_b_asin_title_o01__o00_s00?ie=UTF8&psc=1
   * Hintegrund: Offenbar gibt es Bug im Kernel der bis zu 4.18 reicht - Kernel Fehlermeldung zeugt davon in den Logs (*...link..intel...*) - Kabylake flanscht HDMI und Display Port zusammen - bekommt ihm offenbar nicht
+===== HP MSM720 Wireless Controller =====
+  * Lässt sich über Web Gui -> Maintainance -> Factory Reset resetten
+  * Default IP: **192.168.1.1 über Port 1** , Username: **admin** , Password: **admin**
+  * https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c04227656
+<code>
+NOTE: A factory-default controller is assumed. Ports 1 to 4 are available at 192.168.1.1.
+NOTE: Do not connect power or network cables to the controller until directed to do so in this procedure. If cables are connected, temporarily disconnect them.
+To initially configure the controller:
+    Configure your computer to use a static IP address in the range 192.168.1.2 to 192.168.1.254 and set the subnet mask to 255.255.255.0. Set the default gateway to 192.168.1.1 and DNS server to 192.168.1.1.
+    Connect network cables as follows:
+        Disconnect any cable from your computer Ethernet ports and disable any wireless connection.
+        Connect controller port 1 (ports 2 to 4 can also be used) (the Access network) to your computer Ethernet port.
+        Connect controller port 5T or 6T (or if enabled, port 5S or 6S) (the Internet network) to a network with Internet access or to the PC port of a DSL modem or equivalent.
+    Power on the controller and wait approximately 90 seconds until the Test LED turns off.
+    Perform initial login tasks:
+        Using Microsoft Internet Explorer 8+ or Mozilla Firefox 3+, open page: https://192.168.1.1.
+        A security certificate warning may be displayed the first time you connect to the management tool. This is normal. Select whatever option is needed in your Web browser to continue to the management tool.
+        On the Login page, enter admin for Username and admin for Password and then select Login.
+        On the HP End User License Agreement page, read the agreement and then select Accept HP End User License Agreement.
+        On the product registration page it is recommended that you register your product now by selecting Register Now. If the controller is not connected to the Internet or you prefer not to register now, select Register Later. Registration is available at any time by selecting Maintenance > Registration.
+        In some regions, a Country prompt appears. Choose the country in which this product will be used and select Save.
+        CAUTION: To maintain regulatory compliance, the country must be set accurately to the country in which the controller and any controlled access points (APs) will operate.
+        At the Administrator password prompt it is recommended that you change the password. Select Save to save the new password or Cancel if you choose to keep the default password.
+</code>
 ===== HP ML350 Gen9 / HP Microserver gen8 =====
@@ Zeile 2207: / Zeile 2343: @@
 <code>
-(BRG-Neusiedl) #halt
+(Controller) #halt
 WARNING: THIS COMMAND WILL TERMINATE ALL WEBUI, TELNET AND SSH SESSIONS.
 Please only execute this command from the local console.
@@ Zeile 2214: / Zeile 2350: @@
 Connection to wific1.schule.intern closed.
 </code>
+  * Resetting Controller im # Modus **write erase all** bzw. **write erase** Restart mit **reload** (https://www.arubanetworks.com/techdocs/ArubaOS_62_Web_Help/Content/ArubaFrameStyles/New_Licenses/Resetting_the_.htm)
+<code>
+Resetting the Controller
+Rebooting or resetting a controller has no effect on either permanent or evaluation licenses. Issuing the write erase command on a controller running software licenses does not affect the license key management database on the controller. Issuing the write erase all command resets the controller to factory defaults, and deletes all databases on the controller including the license key management database. You must reinstall all previously-installed license keys.
+</code>
+  * Default IP Zugriff: **https://172.16.0.254:4343/** über zB: 1
+{{:know-how:0-aruba-7010-initialization-after-factory-reset.png?400|}}
 ===== Aruba InstantOn 1930 - 48G 4SFP/SFP+ =====
   * Einzig mir bekannter **lüfterloser** 48Gbit Switch
@@ Zeile 2316: / Zeile 2464: @@
 </code>
   * VHDX File mounten und lesen:
+  * **ACHTUNG** eine Menge an dependencies !
 <code>
@@ Zeile 2322: / Zeile 2471: @@
     guestmount --add BACKUP.vhdx --inspector --ro /mnt
 </code>
 ====== Antiviren-Dashboards ======
 ===== Nanoheal =====